familyname=Lenz 5th gen BEMF decoders
manufacturer=Lenz
lowVersionID=51
highVersionID=54
definitionSource=JMRI
CV=2,"Start Voltage (0-31)Volt Partenza (0-31)V démarr.v (0-31)Startspannung (0-31)Sets the starting voltage at throttle speed step 1.  Note: some decoders only accept a max value of 15"
CV=3,"Acceleration Momentum (0-255)Accellerazione (0-255)Accelération (0-255)Anfahrverzögerung (0-255)Sets the acceleration rate (delay)"
CV=4,"Deceleration (Brake) Momentum (0-255)Inerzia decellerazione (frenata)  (0-255)DecelSets the deceleration rate (delay)"
CV=5,"Maximum Speed (1-10)Velocità massima (1-10)VhighSets the maximum voltage at full throttle (only active if Back EMF enabled)"
CV=7,"Decoder Version No.Versione Decoder: Version décodeur: Decoder Version: "
CV=8,"Manufacturers Identification No.ID Costruttore: ID constructeur: Hersteller ID: "
CV=9,"EMF Frequency (0-15)Frequenza EMF (0-15)Motor PWM FrequencyAdjust EMF pulse rate frequency for finer motor control"
CV=29,","RailCom disabled","RailCom disabledRailCom disabilitataRailCom disabled","RailCom enabled","RailCom enabledRailCom AbilitataRailCom enabled"Lenz RailCom (not used on all decoders)RailCom Lenz (non per tutti i decoder)Lenz RailCom (not used on all decoders)Enables RailCom when used with Lenz systems"
CV=50,","Inactive","InactiveInattivoInactive","Active","ActiveAttivoActive"Back EMF ControlControllo BEMFLoad ControlActivates the Back EMF function"
CV=50,","Loco continues under analog (DC) voltage control","Loco continues under analog (DC) voltage controlLoco continua sotto controllo tensione AnalogicaLoco continues under analog (DC) voltage control","Loco brakes to a stop using momentum set in CV4","Loco brakes to a stop using momentum set in CV4Loco frena fino a fermarsi usando Inerzia impostata in CV4Loco brakes to a stop using momentum set in CV4"When loco enters DC track section: Quando la Loco entra in un Blocco AnalogicoGoverns how loco acts in DC track blockDC Brake MomentumGoverns how loco acts in DC track blockGoverns how loco responds in DC powered track block (Analog Conversion Mode must be OFF)"
CV=51,","Front headlight is always dimmed","Front headlight is always dimmedAttenuazione Luci di testa sempre attivaFront headlight is always dimmed","F1 or F4 controls headlight dimming","F1 or F4 controls headlight dimmingF1 o F4 controllano Attenuazione Luci di testaF1 or F4 controls headlight dimming"Output A Dimming ControlControllo Attenuazione Luci Uscita ACV 52 controls amountCV 52 controlla l'ammontareFunction F0F behaviorCV 52 controls amountDetermines how front headlight dims (when dimming is enabled)Controllo attenuazione luci frontali (quando abilitato)"
CV=51,","Front headlight never dim","Front headlight never dimAttenuazione Luci di testa mai attivaFront headlight never dim","Front headlight can dim","Front headlight can dimAttenuazione Luci di testa possibileFront headlight can dim"Front Headlight (Output A) DimmingAttenuazione Luci di testa (Uscita A)Function F0F effect generatedEnables front headlight dimming"
CV=51,"Output A is a GyrolightUscita A = GyrolightFunction F0F option 1"
CV=51,"Output A is a Mars lightUscita A = Mars lightFunction F0F option 2"
CV=51,"Output A is a single strobeUscita A = strobe singoloFunction F0F option 3"
CV=51,"Output A is a double strobeUscita A = Strobe doppioFunction F0F option 4"
CV=52,"Output A Dimming Intensity (0-255)Uscita A Intensità Attenuazione (0-255)Function F0F optionsSets intensity of dimmed headlight (larger number = brighter light)"
CV=57,","Rear headlight is always dimmed","Rear headlight is always dimmedUscita B (Luci di coda) Sempre AttenuateRear headlight is always dimmed","F1 or F4 controls headlight dimming","F1 or F4 controls headlight dimmingF1 o F4 controllano Attenuazione Luci di codaF1 or F4 controls headlight dimming"Output B Dimming ControlUscita B Controllo AttenuazioneCV 58 controls amountCV 58 controlla l'ammontareFunction F0R behaviorCV 58 controls amountDetermines how rear headlight dims (when dimming is enabled)"
CV=57,","Rear headlight never dim","Rear headlight never dimLuci di coda mai AttenuateRear headlight never dim","Rear headlight can dim","Rear headlight can dimLuci di coda possono essere AttenuateRear headlight can dim"Rear Headlight (Output B) DimmingOutput B Attenuazione Luci di CodaFunction F0R effect generatedEnables rear headlight dimming"
CV=57,"Output B is a GyrolightOutput B = GyroLightFunction F0R option 1"
CV=57,"Output B is a Mars lightOutput B = Mars LightFunction F0R option 2"
CV=57,"Output B is a single strobeOutput B = Strobe singoloFunction F0R option 3"
CV=57,"Output B is a double strobeOutput B = Strobe doppioFunction F0R option 4"
CV=58,"Output B Dimming Intensity (0-255)Uscita B Intensità Attenuazione (0-255)Function F0R optionsSets intensity of dimmed headlight (larger number = brighter light)"
CV=56,"Blinking Rate for Outputs C and D (0-255)Frequenza lampeggio per Uscite C e D (0-255)Function 1 behaviorSets the blinking rate for outputs C and D"
CV=53,"Output C BlinksUscita C lampeggiaFunction 1 optionsOutput C blinks with the frequency set in"
CV=53,"Output D BlinksUscita D lampeggiaFunction 1 option 2Output D blinks with the frequency set in"
CV=53,"Outputs C and D act as Ditch LightsUscita C  e D funzionano come Ditch LightsFunction 1 option 3controls which function turns on both ditch lights and CV54 controls which function activates the alternating blinking"
CV=54,"F1 controls output CF1 controlla Uscita CF1 controls output 3"
CV=54,"F2 controls output CF2 controlla Uscita CF2 controls output 3"
CV=54,"F3 controls output CF3 controlla Uscita CF3 controls output 3"
CV=54,"F4 controls output CF4 controlla Uscita CF4 controls output 3"
CV=54,"F5 controls output CF5 controlla Uscita CF5 controls output 3"
CV=54,"F6 controls output CF6 controlla Uscita CF6 controls output 3"
CV=54,"F7 controls output CF7 controlla Uscita CF7 controls output 3"
CV=54,"F8 controls output CF8 controlla Uscita CF8 controls output 3"
CV=55,"F1 controls output DF1 controlla Uscita DF1 controls output 4"
CV=55,"F2 controls output DF2 controlla Uscita DF2 controls output 4"
CV=55,"F3 controls output DF3 controlla Uscita DF3 controls output 4"
CV=55,"F4 controls output DF4 controlla Uscita DF4 controls output 4"
CV=55,"F5 controls output DF5 controlla Uscita DF5 controls output 4"
CV=55,"F6 controls output DF6 controlla Uscita DF6 controls output 4"
CV=55,"F7 controls output DF7 controlla Uscita DF7 controls output 4"
CV=55,"F8 controls output DF8 controlla Uscita DF8 controls output 4"
CV=105,"User Private ID #1 (0-255)ID Utente Privato #1 (0-255)User Id #1"
CV=106,"User Private ID #2 (0-255)ID Utente Privato #2 (0-255)User Id #2"
CV=128,"Decoder Software VersionVersione Software DecoderDecoder Software VersionThe decoder software version number (read only)"
Reset All CVs to factory defaults (use Register Mode for this)Ripristina tutte le CV ai valori di fabbrica (usare Modalità Registro)LenzLenz