familyname=Harman DIY Accessory Decoders
manufacturer=Harman DCC
definitionSource=JMRI
CV=1,"Low 7 bytes of Address CV1"
CV=9,"High 3 bytes of Address CV9"
CV=1,"Decoder Address (1-511)"
CV=1,"Output Mode Address (1-2047)"
CV=3,"A Output (x10) Millisecs"
CV=4,"B Output (x10) Millisecs"
CV=5,"C Output (x10) Millisecs"
CV=6,"D Output (x10) Millisecs"
CV=1,"                    outputs 1+2"
CV=1,"                    outputs 3+4"
CV=1,"                    outputs 5+6"
CV=1,"                    outputs 7+8"
CV=1,"                    outputs 1+2"
CV=1,"                    outputs 3+4"
CV=1,"                    outputs 5+6"
CV=1,"                    outputs 7+8"
CV=1,"                    outputs 1+2"
CV=1,"                    outputs 3+4"
CV=1,"                    outputs 5+6"
CV=1,"                    outputs 7+8"
CV=1,"                    outputs 1+2"
CV=1,"                    outputs 3+4"
CV=1,"                    outputs 5+6"
CV=1,"                    outputs 7+8"
CV=29,"Accessory Mode Setting"
CV=29,","Decoder Address Mode","","Output Address Mode",""Sequential Address Mode"
CV=33,"Lenz Toggle Mode"
CV=33,","Off","0","On","1"Toggle Mode output 1"
CV=33,","Off","0","On","1"Toggle Mode output 2"
CV=33,","Off","0","On","1"Toggle Mode output 3"
CV=33,","Off","0","On","1"Toggle Mode output 4"
CV=33,","Off","0","On","1"Roco Momentary Mode"
CV=34,","Pin 6","0","Pin 5 or 11","1"Ack Pin"
CV=35,"invert outputs"
CV=35,","No","1","Yes","0"invert output 1"
CV=35,","No","1","Yes","0"invert output 2"
CV=35,","No","1","Yes","0"invert output 3"
CV=35,","No","1","Yes","0"invert output 4"
CV=35,","No","1","Yes","0"invert output 5"
CV=35,","No","1","Yes","0"invert output 6"
CV=35,","No","1","Yes","0"invert output 7"
CV=35,","No","1","Yes","0"invert output 8"
CV=36,"flicker outputs"
CV=36,","No","1","Yes","0"flicker output 1"
CV=36,","No","1","Yes","0"flicker output 2"
CV=36,","No","1","Yes","0"flicker output 3"
CV=36,","No","1","Yes","0"flicker output 4"
CV=36,","No","1","Yes","0"flicker output 5"
CV=36,","No","1","Yes","0"flicker output 6"
CV=36,","No","1","Yes","0"flicker output 7"
CV=36,","No","1","Yes","0"flicker output 8"
Decoder Address Mode           To turn off, use Output Address Mode paneIn Decoder Address Mode, the decoder address is multiplied by four to get the accessory address.An offset of 1 is required to work with Lenz/Digitrax systems when compared to Roco/MERG command stations Lenz (etc) Command Stations  Accessory Address to operate  Roco (etc) Command Stations  Accessory Address to operate Output Duration and Toggle ModeToggle Mode is required for some systems, if in doubt, turn onThe behaviour is the same as with MERG kit built decodersDuration of Output(x10 MilliSecs)0 = continous outputToggle Mode OutputsOutput behaviours:Output Address Mode           To turn off, use Decoder Address Mode paneIn Output Address Mode, the decoder address is the accessory address, there is no multiplication. An offset of 4 is required to work with Lenz/Digitrax systems when compared to Roco/MERG command stations Lenz (etc) Command Stations  Accessory Address to operate  Roco (etc) Command Stations  Accessory Address to operate Output Duration and Toggle ModeToggle Mode is required for some systems, if in doubt, turn onThe behaviour is the same as with MERG kit built decodersDuration of Output(x10 MilliSecs)0 = continous outputToggle Mode OutputsOutput behaviours: