familyname=PM4x
manufacturer=Digitrax
definitionSource=JMRI
LOCONETBDOPSWMODECV=1,"Board Address (Board ID)"
CV=112.01,","","Thrown","","Closed""
CV=112.02,","","Thrown","","Closed""
CV=112.09,","","Thrown","","Closed""
CV=112.03,","","Thrown","","Closed""
CV=112.05,","","Normal","","Slow""
CV=112.06,","","Short-circuit Protection (pins 5 and 6 unconnected)","","Autoreversing (with pin E shorted to pin 5 and pin F shorted to pin 6)""
CV=112.11,","","Thrown","","Closed""
CV=112.13,","","Normal","","Slow""
CV=112.14,","","Short-circuit Protection (pins 9 and 10 unconnected)","","Autoreversing (with pin K shorted to pin 9 and pin L shorted to pin 10)""
CV=112.19,","","Thrown","","Closed""
CV=112.21,","","Normal","","Slow""
CV=112.22,","","Short-circuit Protection (pins 13 and 14 unconnected)","","Autoreversing (with pin P shorted to pin 13 and pin R shorted to pin 14)""
CV=112.27,","","Thrown","","Closed""
CV=112.29,","","Slow","","Normal"Short-Circuit Trip Speed""
CV=112.30,","","Short-circuit Protection (pins 17 and 18 unconnected)","","Autoreversing (with pin U shorted to pin 17 and pin V shorted to pin 18)""
CV=,"Trip Current is"
CV=,"Section 1 Trip Speed is"
CV=,"Section 2 Trip Speed is"
CV=,"Section 3 Trip Speed is"
CV=,"Section 4 Trip Speed is"
OpSwsShort Addressgt0<html>The "CV" column in the table above shows "OpSw" 
                    numbers, where the value "112." is pre-pended
                    <p>to the OpSw Number.  For example, PM4/PM42 OpSw 1 
                    is represented as "112.01".
                    <p><p>The top-most row above reflects the Board 
                    Address configured on the "Basic" sheet.
                    <p><p>OpSw value 0 = "T"hrown.  OpSw value 1 = "C"losed.
                    </html>
                Basic<html><p>
                LocoNet messaging limits the supported Board Address (Board ID)
                range to addresses between 1 and 128.  This tool cannot access PM4/PM42
                <p>devices outside of this range.
                <p>
                <p>This roster entry will only access the specified PM4/PM42 if the
                Board Address (Active Address), on the "Basic" sheet, is correct when the
                <p>programmer is opened.
                <p>
                <p>If the Board Address (Active Address) has been changed since
                the programmer was opened, the programmer will attempt to access the
                <p>PM4/PM42 address which was specified in the Roster entry
                when the progammer was opened.
                <p>
                <p>After making a change to the Roster entry's Board Address
                (Active Address) on the "Basic" sheet, save and close the programmer
                <p>window and re-open the Roster entry to ensure that the
                the programmer will use the modified Active Address for accesses
                <p>to the device.
                <p>
                <p>Note that BDL16x and PM4x documentation refers 
                to Board Address, while DS64 and SE8C documentation refers to 
                <p>Board ID.  These are equivalent concepts.
            </html>Basic Settings<html><span style="color: black;"><h2><strong>Trip Current (all Sections)</strong></h2></html><html><span style="color: black;"><h2><strong>Section 1 Characteristics</strong></h2></html>Mode<html><span style="color: black;"><h2><strong>Section 2 Characteristics</strong></h2></html>Mode<html><span style="color: black;"><h2><strong>Section 3 Characteristics</strong></h2></html>Mode<html><span style="color: black;"><h2><strong>Section 4 Characteristics</strong></h2></html>ModeNotes<html><span style="color: black;">
            <h2><strong>Notes on PM4/PM42 Roster Entries and Programming
            </strong></h2></html><html></strong><ul>
                <li>The PM4/PM42 <em>must</em> be in its normal
                operating mode in order to respond to this Roster entry's read and
                write operations.</li>
                <li>
                <p>See the "Basic" sheet for the programmer's limitations with
                respect to Board Address.</li>
                <li>This Roster entry is not currently capable of 
                displaying the short-circuit and autoreversing status of each section.
                <li>Some PM4 devices do not respond to the LocoNet messages
                used by this tool.  Programming of these devices may 
                <p>be done as described in the PM4 manual.  It is also possible
                to upgrade the PM4 to a PM42 via a simple chip change.
                <p>Upgrade chips may be available from your Digitrax dealer 
                or from Digitrax.
            </ul></html>CVsCVCV-TabelleTaula-CVTabulka CVCV-tabelShort Addresseq0This sheet intentionally un-populated.  See the "OpSws" tab.