familyname=Series 7 Boards
manufacturer=Digitrax
definitionSource=JMRI
LOCONETBD7OPSWMODECV=1,"Board Address "
CV=7,"Device Type"
CV=8,"Device Manufacturer (NMRA number) "
CV=9,"Serial Number"
CV=11,","","2Two Position Servo (Thrown/Closed)","","6Three Position Servo (Semaphore)"Output type: "
CV=11,","","enabled","","disabled"Internal Routes are"
CV=12,","","disabled","","enabled"Bushby Bit is"
CV=12,","","do turnout, sensor commands","","trigger routes"Input Lines"
CV=12,","","Loconet switch commands","","DCC switch commands only"Command source is"
CV=12,","","echo to Loconet","","do not echo to Loconet"Route Switch Commands"
CV=0.25,"SERVO 1 - 'Thrown' Angle:"
CV=0.26,""Closed" Angle:"
CV=0.27,"Output Typeeq6"Approach" Angle:"
CV=0.28,"Output Typeeq6"Approach Medium" Angle:"
CV=1.25,"SERVO 2 - 'Thrown' Angle:"
CV=1.26,""Closed" Angle:"
CV=1.27,"Output Typeeq6"Approach" Angle:"
CV=1.28,"Output Typeeq6"Approach Medium" Angle:"
CV=2.25,"SERVO 3 - 'Thrown' Angle:"
CV=2.26,""Closed" Angle:"
CV=2.27,"Output Typeeq6"Approach" Angle:"
CV=2.28,"Output Typeeq6"Approach Medium" Angle:"
CV=3.25,"SERVO 4 - 'Thrown' Angle:"
CV=3.26,""Closed" Angle:"
CV=3.27,"Output Typeeq6"Approach" Angle:"
CV=3.28,"Output Typeeq6"Approach Medium" Angle:"
CV=4.25,"SERVO 5 - 'Thrown' Angle:"
CV=4.26,""Closed" Angle:"
CV=4.27,"Output Typeeq6"Approach" Angle:"
CV=4.28,"Output Typeeq6"Approach Medium" Angle:"
CV=5.25,"SERVO 6 - 'Thrown' Angle:"
CV=5.26,""Closed" Angle:"
CV=5.27,"Output Typeeq6"Approach" Angle:"
CV=5.28,"Output Typeeq6"Approach Medium" Angle:"
CV=6.25,"SERVO 7 - 'Thrown' Angle:"
CV=6.26,""Closed" Angle:"
CV=6.27,"Output Typeeq6"Approach" Angle:"
CV=6.28,"Output Typeeq6"Approach Medium" Angle:"
CV=7.25,"SERVO 8 - 'Thrown' Angle:"
CV=7.26,""Closed" Angle:"
CV=7.27,"Output Typeeq6"Approach" Angle:"
CV=7.28,"Output Typeeq6"Approach Medium" Angle:"
CVs<html><p>CVs 1 and 2 are the low and high (respectively) 8-bit
                        "Base Address" values.<p>The "Base Address" is practically limited to
                        2029 (in "2-position servo" mode), or <p>2025 (in "3-position
                        Servo" mode).<p>The "Roster" tool and its
                        Roster entries <em> cannot</em> change the
                        "Base Address".Basic<html>
                <p>This roster entry will only access the specified
                board if the Base Address specified above <br>was
                correctly entered when the roster entry was first created.
                You <em>cannot</em> change it in the Roster Entry.
            </html>OpSw Settings<html><span style="color: black;"><h2><strong>Output Controls Characteristics</strong></h2></html><html><span style="color: black;"><p><h2><strong>Output Controls Characteristics</strong></h2></html>Servos<html><span style="color: black;"><h2><strong>Servo Characteristics</strong></h2></html>Output Typeeq2<html><span style="color: black;"><p>
                "Aproach" and "Approach Medium" settings are only used<p>
                when operating in "Three-position" mode.  Those values are<p>
                irrelevant for "Two-position" Servo mode and are not shown<p>
                here.</html>