familyname=DS64
manufacturer=Digitrax
definitionSource=JMRI
LOCONETBDOPSWMODECV=1,"Board ID"
CV=115.01,","","Outputs are pulsed (OpSw1=t)Thrown is first choice; Closed is second choice","","Outputs are static (OpSw1=c)Thrown is first choice; Closed is second choice""
CV=115.02,","","Outputs pulse active or blink for 0.1 second (OpSw2=t)","","Outputs pulse active or blink for 0.2 second (OpSw2=c)""
CV=115.03,","","Add 0 seconds to the pulse or blink rate (OpSw3=t)","","Add 0.3 seconds to the pulse or blink rate (OpSw3=c)""
CV=115.04,","","Add 0 seconds to the pulse or blink rate (OpSw4=t)","","Add 0.7 seconds to the pulse or blink rate (OpSw4=c)""
CV=115.05,","","Add 0 seconds to the pulse or blink rate (OpSw5=t)","","Add 1.5 seconds to the pulse or blink rate (OpSw5=c)""
CV=115.06,","","Outputs automatically power-up to the last known state (OpSw6=t)Thrown is first choice; Closed is second choice","","Each output remain undriven until its turnout command is received (OpSw6=c)Thrown is first choice; Closed is second choice""
CV=115.08,","","Short delay for interrogation requests (OpSw8=t)Thrown is first choice; Closed is second choice","","Long delay for interrogation requests (OpSw8=c)Thrown is first choice; Closed is second choice""
CV=115.09,","","Static Outputs remain powered (OpSw9=t)Thrown is first choice; Closed is second choice","","Static Outputs are shut off after 16 seconds (OpSw9=c)Thrown is first choice; Closed is second choice""
CV=115.10,","","Throttle and Computer commands are accepted (OpSw10=t)Thrown is first choice; Closed is second choice","","Computer commands are accepted (OpSw10=c)Thrown is first choice; Closed is second choice""
CV=115.11,","","Routes are triggered by Switch commands from Computers or Throttles (OpSw11=t)Thrown is first choice; Closed is second choice","","Routes are triggered by DS64 inputs (OpSw11=c)Thrown is first choice; Closed is second choice""
CV=115.12,","","S inputs affect output; A inputs send Sensor messages (OpSw12=t)Thrown is first choice; Closed is second choice","","A input high forces output "Thrown"; S input high forces output "Closed" (OpSw12 = c)Thrown is first choice; Closed is second choice""
CV=115.13,","","Inputs have no effect (OpSw13=t)Thrown is first choice; Closed is second choice","","Inputs act as LocoNet Sensors and also control related outputs per OpSw12 (OpSw13=c)Thrown is first choice; Closed is second choice""
CV=115.14,","","Accepts commands from LocoNet messages and Track (OpSw14=t)Thrown is first choice; Closed is second choice","","Accepts commands from Track only (OpSw14=c)Thrown is first choice; Closed is second choice""
CV=115.15,","","Inputs can control outputs (OpSw15=t)Thrown is first choice; Closed is second choice","","Inputs have no direct effect on outputs (OpSw15=c)Thrown is first choice; Closed is second choice""
CV=115.16,"Routes are"
CV=115.17,","","Output 1 does not provide "crossing-gate" output (OpSw17=t)Thrown is first choice; Closed is second choice","","Output 1 provides "crossing-gate" output (OpSw17=c)Thrown is first choice; Closed is second choice""
CV=115.18,","","Output 2 does not provide "crossing-gate" output (OpSw18=t)Thrown is first choice; Closed is second choice","","Output 2 provides "crossing-gate" output (OpSw18=c)Thrown is first choice; Closed is second choice""
CV=115.19,","","Output 3 does not provide "crossing-gate" output (OpSw19=t)Thrown is first choice; Closed is second choice","","Output 3 provides "crossing-gate" output (OpSw19=c)Thrown is first choice; Closed is second choice""
CV=115.20,","","Output 4 does not provide "crossing-gate" output (OpSw20=t)Thrown is first choice; Closed is second choice","","Output 4 provides "crossing-gate" output (OpSw20=c)Thrown is first choice; Closed is second choice""
CV=115.21,","","Inputs generate LocoNet "General Sensor" messages (OpSw21=t)Thrown is first choice; Closed is second choice","","Inputs generate LocoNet "LocoNet Turnout State" messages (OpSw21=c)Thrown is first choice; Closed is second choice""
CV=,"Outputs pulse or blink at "
CV=,"DS64 Routes"
CV=,"Local Inputs"
CV=,""
OpSwsShort Addressgt0<html>The "CV" column in the table above shows "OpSw" 
                    numbers, where the value "115." is pre-pended
                    <p>to the OpSw Number.  For example, PM4/PM42 OpSw 1 
                    is represented as "115.01".
                    <p><p>The top-most row above reflects the Board 
                    Address configured on the "Basic" sheet.
                    <p><p>OpSw value 0 = "T"hrown.  OpSw value 1 = "C"losed.
                    </html>
                Basic<html><p>
                LocoNet messaging limits the supported Board ID
                range to addresses between 1 and 128.  This tool cannot access DS64s
                <p>outside of this range.
                <p>
                <p>This roster entry will only access the specified DS64 if the
                Board ID, on the "Basic" sheet, is correct when the
                <p>programmer is opened.
                <p>
                <p>If the Board ID has been changed since
                the programmer was opened, the programmer will attempt to access the
                <p>DS64 address which was specified in the Roster entry
                when the progammer was opened.
                <p>
                <p>After making a change to the Roster entry's Board ID
                (Active Address) on the "Basic" sheet, save and close the programmer
                <p>window and re-open the Roster entry to ensure that the
                the programmer will use the modified Active Address for accesses
                <p>to the device.
                <p>Note that BDL16x and PM4x documentation refers 
                to Board Address, while DS64 and SE8C documentation refers to 
                <p>Board ID.  These are equivalent concepts.
            </html>DS64 Basic Settings<html><span style="color: black;"><h2><strong>Output Controls Characteristics</strong></h2></html><html><span style="color: black;"><h2><strong>Control Source Characteristics</strong></h2></html><html><span style="color: black;"><h2><strong>Local Routes Characteristics</strong></h2></html><html><span style="color: black;"><h2><strong>Local Input Signals Characteristics</strong></h2></html>Notes<html><span style="color: black;">
            <h2><strong>Notes on DS64 Roster Entries and Programming
            </strong></h2></html><html></strong><p><ul>
                <li>
                The DS64 <em>must</em> be in its normal
                operating mode in order to respond to this Roster entry's read and
                write operations.</li>
                <li>
                <p>See the "Basic" sheet for the programmer's limitations with
                respect to Board ID.</li>
                <li><p>This Roster entry is not currently capable of displaying, changing, or saving the DS64 output addresses.</p></li>
                <li><p>This Roster entry is not currently capable of displaying, changing, or saving the DS64 Routes.</p></li>
            </ul></html>CVsCVCV-TabelleTaula-CVTabulka CVCV-tabelShort Addresseq0This sheet intentionally un-populated.  See the "OpSws" tab.