familyname=Series 7 Boards
manufacturer=Digitrax
definitionSource=JMRI
LOCONETBD7OPSWMODECV=1,"Board Address"
CV=7,"Device Type"
CV=8,"Device Manufacturer (NMRA number) "
CV=9,"Serial Number"
CV=11,","0","Normal Sensitivity","1","Higher Sensitivity","2","Lower Sensitivity","3","(unknown sensitivity)"Detection uses "
CV=11,","","Normal","","Slow"Detection speed is "
CV=12,","","Forces all detection to "occupied"","","has no effect on occupancy reporting"Track power "off" "
CVs<html>The "CV" column in the table above shows CV
                        numbers, not the Op Switch number.<p>To see those, hover
                        your mouse over a variable on the OpSw Settings pane.
                        <p>CVs 1 and 2 are the low and high (respectively) 8-bit
                        "Base Address" values.<p>The "Base Address" is practically
                        limited to 2040, max.<p>The JMRI "Roster" tool and its
                        Roster entries <em> cannot</em> change the
                        "Base Address".
                    Basic<html>
                <p>This roster entry will only access the specified
                board if the Base Address specified above <br>was
                correctly entered when the roster entry was first created.
                You <em>cannot</em> change it in the Roster Entry.
            </html>OpSw Settings<html><h2>Detection SettingsNotes<html><h2>Notes:</h2>
                  <ul>
                  <li>The BDL716 device implements features that "use" various
                  types of addresses in<br>
                  several types of "Address Spaces".  It is important that the
                  device <em>only</em> uses those<br>
                  addresses that are <em>not</em> used by any other device,
                  whether on LocoNet or connected<br>
                  to the "DCC Track" signal. </li>
                  <li>The BDL716 is believed to use the addresses as described below:<br>
                  <table border="3">
                    <tr><th>Address Type</th>
                    <th>Range of Addresses</th>
                    <th>Comments</th></tr>

                    <tr><td>Sensors</td>
                    <td>Base Address to<br>(Base Address + 15)</td>
                    <td>The BDL716 implements 16 "Detection<br>
                              Sensors" in the LocoNet sensor address<br>
                              range.</td>
                    </tr>

                    <tr><td>Switches</td>
                    <td>(None)</td>
                    <td>The BDL716 does not implement any<br>
                              "Turnout"s in either the LocoNet or<br>
                              the "NMRA Accessory" address range.</td>
                    </tr>

                    <tr><td>NMRA "Extended<br>Accessories"
                    <br>(Signal Aspect<br>Accessories)</td>
                    <td>Base Address to<br>(Base Address + 3)</td>
                    <td>The BDL716 uses NMRA "Extended<br>
                              Accessory" ("Signal Aspect") <br>
                              addresses for accessing Device<br>
                              "CV" settings, but does not otherwise<br>
                              implement any "Extended Accessory"<br>
                              addresses.</td>
                    </tr>

                    <tr><td>Transponding<br>"Zones"</td>
                    <td>(None)</td>
                    <td>The BDL716 does not implement any<br>
                              "Transponding" addresses in the<br>
                              LocoNet Transponding address range.</td>
                    </tr>

                    <tr><td>"Power/Track<br>Status"</td>
                    <td>(None)</td>
                    <td>The BDL716 does not implement any<br>
                              addresses in the LocoNet "Power/<br>
                              Track Status" address range.</td>
                    </tr>
                  </table>

              <li>The BDL716's CVs can be mapped to a "Base Address" that
                        "overlaps" another<br;>
                        device on this LocoNet connection, or otherwise
                        conflicts with an NMRA<br;>
                        Extended Accessory decoder.<br;>
                        <em>When programming with this roster entry, such a conflict
                        can cause the conflicting<br;>
                        device to be mistakenly configured.</em></li>
              <li>Because the DT602 or other mechanisms (like this roster entry!)
                  can access this<br;>
                  BDL716 device's CVs by any of a number of "device addresses"
                  (See 'NMRA<br>
                  "Extended Accessories" in the table above), this roster entry's
                  "Board Address"<br;>
                  should be configured to the actual device's Base Address. This
                  will reduce the<br;>
                  likelihood of mis-configuring this BDL716 or any other device
                  that may be<br;>
                  configured by this type of configuration method, whether a
                  LocoNet peripheral or</li>
                  some other kind of device.</li>
              <li>Because of the notes above, </em>it is recommended</em>
                  that this BDL716 roster entry <br;>
                  should be set to the BDL716's "Base Address" setting, and that
                  care must be taken<br;>
                  to avoid other devices from using addresses that this BDL716
                  will use.</ul></html>