familyname=BDL16x
manufacturer=Digitrax
definitionSource=JMRI
LOCONETBDOPSWMODECV=1,"Board Address (Board ID)"
CV=113.01,","","Direct Home Wiring","","Whole-layout Common Rail Wiring"Wiring type is"
CV=113.03,","","normal","","reversed (pay attention to other RailSync wire)"LocoNet cabling is"
CV=113.05,","","Disable Transponding","","Enable Transponding""
CV=113.06,","","Enable Transponding","","Unsupported""
CV=113.07,","","Enable Transponding","","Unsupported""
CV=,"Transponding is "
CV=113.09,","","report occupied when zone power is off","","are not forced when zone power is off"Detection Sections"
CV=113.10,","","is a normal Detection Section","","is a Zone Power ON qualifier for whole-layout common-rail wired systems"Detection Section 16"
CV=113.11,","","acts as the LocoNet Master","","is not the LocoNet Master"This BDL16x"
CV=113.12,","","provides LocoNet termination","","does not terminate LocoNet"This BDL16x"
CV=113.13,","","Wait for 5-second power-up delay (for DB150 compatibility)","","Wait for 0.5 second power-up delay"This BDL16x will"
CV=113.19,","","Resistance below about 22K Ohms is shown as Occupied","","Resistance below about 10K Ohms is shown as Occupied"Detection Section Sensitivity:"
CV=113.25,","","Thrown","","Closed""
CV=113.26,","","Thrown","","Closed""
CV=113.30,","","Thrown","","Closed""
CV=113.31,","","Thrown","","Closed""
CV=,"Sampling of RailSync is "
CV=,"BDL16x LED outputs "
CV=113.36,","","Responds with status at GPON and interrogate commmands","","Responds only to interrogate commmands""
CV=113.42,","","Standard interrogation","","Ignore OpSw36 setting; reply at every interrogation""
CV=,""
CV=113.37,","","Thrown","","Closed""
CV=113.38,","","Thrown","","Closed""
CV=,"Detection Section timing is"
CV=113.39,","","Sequential Mode","","Verbose Mode"Transponder Tracking uses"
CV=113.43,","","Thrown","","Closed""
CV=113.44,","","Thrown","","Closed""
CV=,"BDL16x LED outputs "
CV=113.45,","","sends Transponding messages","","does not send Transponding messages"At reception of GPOFF: "
OpSwsShort Addressgt0<html>The "CV" column in the table above shows "OpSw"
                        numbers, where the value "113." <p>is pre-pended to 
                        the OpSw Number.
                        <p><p>The top-most row above reflects the Board 
                        Address configured on the "Basic" sheet.
                    <html><p>For example, BDL16 OpSw 1 
                        is represented as "113.01".<p></html>
                    <html><p>For example, BDL162 OpSw 1 
                        is represented as "113.01".<p></html>
                    <html><p>For example, BDL168 OpSw 1 
                        is represented as "113.01".<p></html>
                    <html>
                    <p><p>OpSw value 0 = "T"hrown.  OpSw value 1 = "C"losed.<p>
                    </html></html>
                Basic<html><p>
                LocoNet messaging limits the supported Board Address (Board ID)
                range to addresses between 1 and 128.  This tool cannot access 
                <p>BDL16x devices outside of this range.
                <p>
                <p>This roster entry will only access the specified 
                BDL16x if the Board Address (Active Address), on the 
                <p>"Basic" sheet, is correct when the programmer is opened.
                <p>
                <p>If the Board Address (Active Address) has been changed since
                the programmer was opened, the programmer will attempt to access the
                <p>BDL16x address which was specified in the 
                Roster entry when the progammer was opened.
                <p>
                <p>After making a change to the Roster entry's Board Address
                (Active Address) on the "Basic" sheet, save and close the programmer
                <p>window and re-open the Roster entry to ensure that the
                the programmer will use the modified Active Address for accesses
                <p>to the device.
                <p>
                <p>Note that BDL16x and PM4x documentation refers 
                to Board Address, while DS64 and SE8C documentation refers to 
                <p>Board ID.  These are equivalent concepts.
            </html>Basic OpSw Settings<html><span style="color: black;"><h2><strong>Detection Characteristics</strong></h2></html><html><span style="color: black;"><h2><strong>LocoNet Characteristics</strong></h2></html><html><span style="color: black;"><h2><strong>LED Output Characteristics</strong></h2></html>Transponding Controls<html><span style="color: black;"><h2><strong>Transponding Characteristics</strong></h2></html>Notes<html><span style="color: black;">
            <h2><strong>Notes on BDL16 Roster Entries and Programming
            </strong></h2></html><html></strong><ul>
                <li>The BDL16 <em>must</em> be in its normal
                operating mode in order to respond to this Roster entry's read and
                write operations.</li>
                <li>
                <p>See the "Basic" sheet for the programmer's limitations with
                respect to Board Address.</li>
            </ul></html><html><span style="color: black;">
            <h2><strong>Notes on BDL162 Roster Entries and Programming
            </strong></h2></html><html></strong><ul>
                <li>The BDL162 <em>must</em> be in its normal
                operating mode in order to respond to this Roster entry's read and
                write operations.</li>
                <li>
                <p>See the "Basic" sheet for the programmer's limitations with
                respect to Board Address.</li>
            </ul></html><html><span style="color: black;">
            <h2><strong>Notes on BDL168 Roster Entries and Programming
            </strong></h2></html><html></strong><ul>
                <li>The BDL168 <em>must</em> be in its normal
                operating mode in order to respond to this Roster entry's read and
                write operations.</li>
                <li>
                <p>See the "Basic" sheet for the programmer's limitations with
                respect to Board Address.</li>
            </ul></html>CVsCVCV-TabelleTaula-CVTabulka CVCV-tabelShort Addresseq0This sheet intentionally un-populated.  See the "OpSws" tab.